NXP TEF6686 auf Arduino
Re: NXP TEF6686 auf Arduino
Rotary encoder war mir völlig festgelaufen. Mit ein bischen WD-40 Spray klappt es wieder. (Hätte neue bestelt aber falsches Model.)
Re: NXP TEF6686 auf Arduino
For whomever is interested in buying a TEF6686 based radio.
I recently purchased https://de.aliexpress.com/item/1005005937598808.html
This radio is 100% compatible with the TEF DSP AM/FM Tuner v1 from pe5pvb. It came with PE5PVB's software v1.15 installed. It has a reset button accessible from the outside, but no boot button. However.... on the inside there are two unpopulated pads for connecting a boot-switch. One can easily mount a pin header with 2.54mm pitch and connect wires and a (dip)switch. This radio uses a CH340 usb->serial chip, and the recommended programming baudrate is 115200 with flash_freq 40MHz.
I was able to install v1.16 without any issues and also the other firmware as advertised here viewtopic.php?p=1727781#p1727781.
I recently purchased https://de.aliexpress.com/item/1005005937598808.html
This radio is 100% compatible with the TEF DSP AM/FM Tuner v1 from pe5pvb. It came with PE5PVB's software v1.15 installed. It has a reset button accessible from the outside, but no boot button. However.... on the inside there are two unpopulated pads for connecting a boot-switch. One can easily mount a pin header with 2.54mm pitch and connect wires and a (dip)switch. This radio uses a CH340 usb->serial chip, and the recommended programming baudrate is 115200 with flash_freq 40MHz.
I was able to install v1.16 without any issues and also the other firmware as advertised here viewtopic.php?p=1727781#p1727781.
Re: NXP TEF6686 auf Arduino
nice Infosternsel hat geschrieben: ↑Fr 1. Sep 2023, 10:35 For whomever is interested in buying a TEF6686 based radio.
I recently purchased https://de.aliexpress.com/item/1005005937598808.html
This radio is 100% compatible with the TEF DSP AM/FM Tuner v1 from pe5pvb. It came with PE5PVB's software v1.15 installed. It has a reset button accessible from the outside, but no boot button. However.... on the inside there are two unpopulated pads for connecting a boot-switch. One can easily mount a pin header with 2.54mm pitch and connect wires and a (dip)switch. This radio uses a CH340 usb->serial chip, and the recommended programming baudrate is 115200 with flash_freq 40MHz.
I was able to install v1.16 without any issues and also the other firmware as advertised here viewtopic.php?p=1727781#p1727781.
Standort: 10E14 / 51N49, 360m ü. N.N., LdKr. Osterode/Harz
UKW-FM PORTABEL: Verschiedene TEF6686 Tuner , 9-ELE. Eigenbau nach P.Körner, 9.2 nach Körner von Antennenland
DAB+ : Roberts expression mit Teleskopantenne
UKW-FM PORTABEL: Verschiedene TEF6686 Tuner , 9-ELE. Eigenbau nach P.Körner, 9.2 nach Körner von Antennenland
DAB+ : Roberts expression mit Teleskopantenne
Re: NXP TEF6686 auf Arduino
Bild, Ton, Empfang, was sind die Eindrücke?
Re: NXP TEF6686 auf Arduino
画面、声音、接待,印象如何?
-
- Beiträge: 1395
- Registriert: Fr 31. Aug 2018, 17:42
Re: NXP TEF6686 auf Arduino
Schade dass man nicht den Boot Schalter von aussen zugänglich gemacht hat.
Reset braucht man eigentlich nicht weil man ein und ausschalten kann.
Kann man das umändern ? Besonders wenn man sowiso selber einen Boot Schalter einlöten müsste?
Reset braucht man eigentlich nicht weil man ein und ausschalten kann.
Kann man das umändern ? Besonders wenn man sowiso selber einen Boot Schalter einlöten müsste?
Re: NXP TEF6686 auf Arduino
Mein neues TEF6686-Radio hat seit kurzem nahezu keinen Empfang mehr, nur die Ortssender gehen schwach... Es hat aber auch noch die v1.15 installiert, ich kam noch nicht dazu das Gerät aufzuschrauben und einen Boot-Schalter dranzulöten, um die Firmware zu aktualisieren. Liegt das einfach an der alten Firmware oder ist es ein Fehler/Defekt am Gerät?
Edit: Scheint an der Antennenbuchse zu liegen, jenachdem wie man die Antenne dreht ist der Empfang wieder da.
Edit: Scheint an der Antennenbuchse zu liegen, jenachdem wie man die Antenne dreht ist der Empfang wieder da.
Re: NXP TEF6686 auf Arduino
Differences in RDS decoding (RT) between firmware version 1.18 and the latest beta 2.00:
https://files.fm/f/kbaqqdvqe
https://files.fm/f/kbaqqdvqe
-
- Beiträge: 5773
- Registriert: Sa 1. Sep 2018, 19:11
- Wohnort: Arnoldstein, Bezirk Villach Land, Österreich
- Kontaktdaten:
Re: NXP TEF6686 auf Arduino
What are your RT settings?
-
- Beiträge: 5773
- Registriert: Sa 1. Sep 2018, 19:11
- Wohnort: Arnoldstein, Bezirk Villach Land, Österreich
- Kontaktdaten:
Re: NXP TEF6686 auf Arduino
Check with buffering off please. The signal is very poor and disturbed.
Re: NXP TEF6686 auf Arduino
What good are of these 3 options when they just mess up the RDS decoding???
-
- Beiträge: 5773
- Registriert: Sa 1. Sep 2018, 19:11
- Wohnort: Arnoldstein, Bezirk Villach Land, Österreich
- Kontaktdaten:
Re: NXP TEF6686 auf Arduino
Because these are several stages of reliable information.
During Es season we got lot of wrong PI codes which was quite annoying. Then the author improved the RDS information.
Buffering is needed for scroll text (ticker).
But you will never find two identical hardware so it's hard to compare two TEFs in parallel. You see it in your video. It's a question of seconds in this propagation.
If you really want to compare, please use two RDSSPY connections.
During Es season we got lot of wrong PI codes which was quite annoying. Then the author improved the RDS information.
Buffering is needed for scroll text (ticker).
But you will never find two identical hardware so it's hard to compare two TEFs in parallel. You see it in your video. It's a question of seconds in this propagation.
If you really want to compare, please use two RDSSPY connections.
Re: NXP TEF6686 auf Arduino
Tatsächlich - der festgefressene Impulsgeber in meinem ersten TEF6686 wurde mit ein paar Tropfen WD40 auch wieder beweglich und damit funktionsfähig. Das Ersatzteil ist zwar spottbillig, aber das Rauslöten des defekten Teils aus der Platine wäre nicht trivial gewesen. Also danke für den Tipp!
Die Antennenbuchse scheint ein paar Mikrometer von der SMA-Norm abzuweichen, deshalb "wackelt" der Kontakt mehr oder weniger. Bei mir hilft es, den Stecker nicht ganz reinzudrehen. Ich bin mir nicht sicher, ob das angeschlossene Kabel im Innern nicht auch eine Rolle spielt. Am besten würde man das billige Gerümpel inkl. der Original-Teleskopantenne rauswerfen und durch qualitativ bessere Materialien ersetzen.Vilkert hat geschrieben: ↑Do 7. Sep 2023, 16:20 Mein neues TEF6686-Radio hat seit kurzem nahezu keinen Empfang mehr, nur die Ortssender gehen schwach... Es hat aber auch noch die v1.15 installiert, ich kam noch nicht dazu das Gerät aufzuschrauben und einen Boot-Schalter dranzulöten, um die Firmware zu aktualisieren. Liegt das einfach an der alten Firmware oder ist es ein Fehler/Defekt am Gerät?
Edit: Scheint an der Antennenbuchse zu liegen, jenachdem wie man die Antenne dreht ist der Empfang wieder da.
73 de Uli
UKW/TV-Arbeitskreis, FMLIST und REFLEXION
QTH: Lörrach, JN37TO
QTH: Lörrach, JN37TO